Blue, removable Thread Locker prevents threaded metal fasteners, nuts, bolts, and screws from loosening. Thread Locker is an advanced anaerobic adhesive. Pacer Technology Super Glue Blue Threadlocker (15190) is a premium grade product used to lock or seal metal threaded components or for metal fasteners up to ¾” in diameter. This product prevents loosening due to high vibration. Parts can be disassembled with simple hand tools. PROPERTIES: Appearance – blue liquid with mild odor. USE INSTRUCTIONS: For best results, parts should be clean and dry. Apply a bead around the part to be bonded & assemble with a twisting motion to spread adhesive. Allow to cure 24 hours for maximum strength. Excess adhesive on outside of parts will not cure and can be removed with a solvent-soaked cloth. STORAGE AND SHELF LIFE Recap for storage. A one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS CAUTION: IRRITATING TO EYES AND SKIN. Contains methacrylate esters and cumene hydroperoxide. Avoid contact with eyes and skin. May cause skin dermatitis on prolonged contact with sensitive individuals. In case of eye contact, rinse immediately with plenty of water and seek medical advice. Wash skin thoroughly with soap and water after use. Seek medical advice if skin irritation persists. KEEP OUT OF REACH OF CHILDREN.
$18.00
Red, permanent Thread Locker prevents loosening by filling in the inner spaces in threaded metal parts to form a tough solid assembly. Pacer Technology Super Glue Red Threadlocker (15191) is a high strength premium grade product used to permanently lock or seal metal threaded components or for metal fasteners up to 1” in diameter. Also prevents loosening due to high vibration. Appearance – red liquid with mild odour. Use Instructions: For best results, parts should be clean and dry. Apply a bead around the part to be bonded & assemble with a twisting motion to spread adhesive. Allow curing 24 hours for maximum strength. The excess adhesive on the outside of parts will not cure and can be removed with a solvent-soaked cloth. Storage and shelf life: Recap for storage. A one-year shelf life can be expected. CAUTION: IRRITATING TO EYES AND SKIN. Contains methacrylate esters and cumene hydroperoxide. Avoid contact with eyes and skin. May cause skin dermatitis on prolonged contact with sensitive individuals. In case of eye contact, rinse immediately with plenty of water and seek medical advice. Wash skin thoroughly with soap and water after use. Seek medical advice if skin irritation persists. KEEP OUT OF REACH OF CHILDREN.
$9.95
Blue, removable Thread Locker prevents threaded metal fasteners, nuts, bolts, and screws from loosening. Thread Locker is an advanced anaerobic adhesive. Pacer Technology Super Glue Blue Threadlocker (15190) is a premium grade product used to lock or seal metal threaded components or for metal fasteners up to ¾” in diameter. This product prevents loosening due to high vibration. Parts can be disassembled with simple hand tools. PROPERTIES: Appearance – blue liquid with mild odor. USE INSTRUCTIONS: For best results, parts should be clean and dry. Apply a bead around the part to be bonded & assemble with a twisting motion to spread adhesive. Allow to cure 24 hours for maximum strength. Excess adhesive on outside of parts will not cure and can be removed with a solvent-soaked cloth. STORAGE AND SHELF LIFE Recap for storage. A one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS CAUTION: IRRITATING TO EYES AND SKIN. Contains methacrylate esters and cumene hydroperoxide. Avoid contact with eyes and skin. May cause skin dermatitis on prolonged contact with sensitive individuals. In case of eye contact, rinse immediately with plenty of water and seek medical advice. Wash skin thoroughly with soap and water after use. Seek medical advice if skin irritation persists.KEEP OUT OF REACH OF CHILDREN.
$12.50
LOCTITE® 249 is a blue, dimethacrylate ester acrylic film thread locker. It is supplied in a low tack film to provide a convenient and easy to use package, especially where a liquid product may be too fluid to stay on a part or be difficult to apply. This product can be used for immediate assembly or days later and provide consistent strength on a variety of metal substrates. Dimethacrylate ester acrylic film threadlocker. It is supplied in a low tack film to provide a convenient and easy to use package. Designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand tools Supplied in a low tack film to provide a convenient and easy to use package Can be used for immediate assembly or days later Provides consistent strength on a variety of metal substrates Technical Information Color Blue Cure Type Activator Cure, Anaerobic Cure Full Cure Temperature 77 °F Key Characteristics No Mix Number of Components 1 Part Physical Form Film Storage Temperature 46 - 69 °F Technology Acrylic Temperature -65 - 300 °F Thread Size (Maximum) R3/4" Torque Break on M10 Steel 74 in./lb. Torque Prevail on M10 Steel 47 in./lb. Viscosity 8700 mPa.s (cP) Brookfield Viscosity Temperature 25 °C
$16.08
LOCTITE 660 is a high strength retaining compound with good gap filling properties, ideal for repairing worn-out seats, keys, splines, bearings or tapers without remachining. LOCTITE® 660 is designed for the bonding of cylindrical fitting parts, particularly where bond gaps occurs without the need for remachining. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. LOCTITE 660 exhibits excellent gap cure characteristics and is also suitable for retaining shims. Ideal for repairing worn parts without remachining Enables re-use of worn bearing seats, keys, splines or tapers Suitable for retaining shims P1 NSF Reg. No.: 123704 Technical Information Agency Approvals / Specifications NSF P1 Color Silver Diametrical Clearance (Maximum) Unit mm Fixture Time 15 min. Fixture Time Temperature 15 °C Gap Fill 0.5 mm Key Characteristics Thixotropic Substrates Metal: Steel
$10.59
Thread Sealant - medium strength. For fine threads in hydraulic, pneumatic and general fittings. Fast curing. LOCTITE® 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part. Ideal for fine threads as used in hydraulic, pneumatic & general fittings Suitable for metal threads only Instant low-pressure seal Resistant to fuel, oil, coolants and hydraulic fluids Locks connection against vibration loosening PRODUCT DESCRIPTION LOCTITE® 542 provides the following product characteristics: Technology Acrylic Chemical Type Dimethacrylate ester Appearance (uncured) Brown liquidLMS Components One component - requires no mixing Viscosity Low Cure Anaerobic Secondary Cure Activator Application Thread sealing Strength Medium Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry. 2. If the material is an inactive metal or the cure speed is too slow, spray all threads with and allow to dry. 3. Apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also. 4. Using compliant practices, assemble and wrench tighten fittings in accordance with manufacturers recommendations. 5. Properly tightened fittings will seal instantly to moderate pressures. For maximum pressure resistance and solvent resistance allow the product to cure a minimum of 24 hours. For Disassembly 1. Remove with standard hand tools. 2. Where hand tools do not work because of excessive engagement length or large diameters (over 1"), apply localized heat to approximately 250 °C. Disassemble while hot. For Cleanup 1. Cured product can be removed with a combination of soaking in a Loctite solvent and mechanical abrasion such as a wire brush.
$12.26
LOCTITE 518 is a medium-strength, general purpose gasketing product with excellent contamination tolerance. Ideal for use on casted iron, steel and aluminum flanges. LOCTITE® 518 cures when confined in the absence of air between close-fitting metal surfaces. It is an anaerobic gasketing material designed for use on rigid iron, aluminum, and steel flanged mating surfaces. LOCTITE 518 fills gaps up to 0.25mm and forms a flexible, chemical-resistant seal that will not tear or decay. Parts disassemble easily, even after extended service. Typical applications include sealing close-fitting joints between rigid metal faces and flanges. It is also used as a formed-in-place gasket on rigid flanged connections, e.g. transmissions and motor housings. Semi-flexible, medium-strength anaerobic flange gasket Easy to automate Reduces process costs – eliminates manual assembly of conventional gaskets NSF P1 Reg. No. 123758 For active and inactive rigid metal flanges Cures through minor surface contamination Adapts to flange surface irregularities and gaps up to 0.25 mm Gel-type consistency Seals instantly against low pressure Reduces inventory costs – no need for large inventory of cut gaskets Resists high pressure when fully cured No compression set or misaligned gaskets Technical Information Applications Rigid Assembly Gasketing Colour Red Cure Schedule Temperature (Step 1) 200 Cure Schedule Temperature Unit (Step 1) °C Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.3 mm Shelf Life Temperature -40 °C Specific Gravity 1.1 g/l Specific Gravity Temperature 25 °C Substrates Metal: Aluminum Temperature -65 - 300 °F Tensile Shear Strength 7.5 N/mm² Viscosity 500000 - 1000000 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$9.95
LOCTITE 290 is a medium/high strength, wicking grade threadlocking adhesive that is ideal for locking preassembled fasteners. LOCTITE® 290 is a liquid medium/high-strength threadlocker designed for the locking and sealing of threaded fasteners. Because of its low viscosity and capillary action, the product wicks between engaged threads and eliminates the need for disassembly prior to application. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The product can also fill porosities in welds, castings and powdered metal parts. Ideal for locking preassembled fasteners, e.g. instrumentation fasteners, electrical connectors and set screws Works on metal only Proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids Requires heat for disassembly
$12.48
LOCTITE 263 is designed for the permanent locking and sealing of threaded fasteners. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. It's particularly suited for heavy duty applications such as studs into motor housings, nuts onto studs in pump housings and other fasteners where high strength is required. LOCTITE 263 provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids. Recommended on High strength Locks studs against vibration loosening Controlled/torque tension Prevents thread corrosion Fast curing How to use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole. For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours. Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush. For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 4. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 5. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 6. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 7. Assemble and tighten as required For Disassembly 1. Apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush
$14.98
Threadlocking Adhesive - medium strength. General purpose. Suitable for all metal threaded assemblies. LOCTITE® 243 is a general purpose threadlocker of medium bond strength. This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration. The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces. It is proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids. Prevents loosening on vibrating assemblies, e.g. pumps, gearboxes or presses. Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces). Proven to tolerate minor contamination by industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids Permits disassembly with hand tools for servicing Technology: Acrylic Chemical Type: Dimethacrylate ester Appearance (uncured) Blue liquidLMS Fluorescence Positive under UV lightLMS Components One component - requires no mixing Viscosity Medium, thixotropic Cure Anaerobic Secondary Cure Activator Application Threadlocking Strength Medium LOCTITE® 243™ is designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand toolsThe product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature of LOCTITE® 243™ reduces the migration of liquid product after application to the substrateLOCTITE® 243™ provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Safety Data Sheet (SDS). Where aqueous washing systems are used to clean the surfaces before bonding, it is important to check for compatibility of the washing solution with the adhesive. In some cases, these aqueous washes can affect the cure and performance of the adhesive. This product is not normally recommended for use on plastics (particularly thermoplastic materials where stress cracking of the plastic could result). Users are recommended to confirm the compatibility of the product with such substrates. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. Shake the product thoroughly before use 4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 5. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 6. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 7. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 8. Assemble and tighten as required For Disassembly 1. Remove with standard hand tools 2. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot 3. Apply localized heat to the assembly to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush
$17.12
Loctite 222 Threadlocker prevents corrosion, loosening from shock or vibration, and seals to prevent leakage. It also allows for simple, hand tool disassembly without shearing the screw. Easy to remove, it is typically used with small screws up to 1/4 inch. Recommended on Low strength Stops vibration loosening of screws and seals against leakage Prevents thread corrosion Dismantle with normal hand tools How to Use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole. For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours. Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush. For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot.
$19.23
Hold It Australia T90 PENETRATOR Wicking Grade for Close Fitting Parts - 50ml Description: HOLDIT AUSTRALIA T90 Penetrant is a fast-curing, low viscosity anaerobic compound that seeks voids in assembled components to cure anaerobically on close-fitting metal parts. It's ideal for securing tightly fitted assemblies. Applications T90 is excellent for post-assembly application, effectively preventing loosening of metal threaded fasteners. It is suitable for securing parts with minimal clearance and repairing hairline cracks in metal castings. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. For porosity or hairline cracks in casting products, brush directly onto the parts. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia T77 STUDLOCK High Strength for Bolts 25mm and Above - 50ml Description: HOLDIT AUSTRALIA T77 Studlock large diameter high strength threadlocker is a red, general purpose adhesive for permanent threaded assemblies. It effectively locks fasteners 1 and larger in diameter, providing a seal against leakage and corrosion while resisting attacks from lubricants and industrial liquids and gases. Applications Ideal for eliminating double nutting/welding in critical assemblies. T77 allows for reduced casting thickness and prevents cracked castings from interference fit stresses. Suitable for larger diameter studs with coarse threads and can be used to reclaim worn stud holes. Primers are recommended for large gaps and poorly fitting parts. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia T72 STUDLOCK High Temp High Strength for Bolts 25mm and Above - 50ml Description: HOLDIT AUSTRALIA T72 Studlock is a High Strength-High Temperature Threadlocker. This red, single component, anaerobic adhesive is ideal for joining threaded parts exposed to operating temperatures up to 232°C. Its enhanced chemistry allows superior performance at temperatures significantly higher than other thread locking products. Applications T72 is perfect for high-temperature locking and sealing of studs, nuts, screws, bolts, and fittings. It effectively locks and seals parts against leakage, contamination, and corrosion, particularly suitable for larger diameter, coarse-threaded parts. Recommended for components not requiring routine maintenance, as disassembly can be challenging and may require heat. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia T71 THREADLOCK High Strength, Low Viscosity - 50ml Description: HOLDIT AUSTRALIA T71 Threadlock is a high-strength, anaerobic thread locking compound. T71 is developed for the permanent locking of threaded fasteners and performs well on aluminium, steel, plated fasteners, stainless steel, and special alloy parts. It boasts good temperature stability and solvent resistance. Applications T71 is designed to lock and seal large fasteners, especially in applications where shock and vibration might cause loosening. Its high strength ensures a reliable lock in demanding environments. Instructions for Use Clean all surfaces with a cleaning solvent and let them dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or to the internal threads of a blind hole. Assemble the components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia STUDLOCK Mid Strength Lubricated for Torque Assembly - 50ml Description: HOLDIT AUSTRALIA T62 Lubricated Thread Locker is a medium strength, anaerobic thread locking compound, perfect for permanent locking of threaded fasteners. T62 is effective on aluminium, steel, plated, stainless steel, and special alloy parts. It is characterized by its good temperature and solvent resistance. Applications Designed for locking and sealing large fasteners (1 and larger), T62 is ideal for applications where shock and vibration may cause fasteners to loosen, ensuring a stable and permanent lock. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal adhesion. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying any load. Active & Inactive Metal Table Consult the Active and Inactive Metal Table for specific application guidance on different metal types.
$34.86
Hold It Australia T43 NUTLOCK Medium Strength (Oil Tolerant) - 50ml Description: HOLDIT AUSTRALIA T43 Nutlock is an oil tolerant, medium viscosity, Thixotropic, anaerobic thread locking adhesive suitable for all types of metal threaded fasteners. The cured adhesive offers controlled medium strength, excellent temperature, and solvent resistance, particularly against water and nonpolar solvents. It rapidly cures on plated, oily metal surfaces or inactive surfaces. Applications Ideal for replacing lock washers and plastic inserts, NUTLOCK locks machine tool access bolts, studs, hydraulic system bolts, gear box bolts/drive shaft, bearing cover cap screws, counter sunk screws, conveyor roller bolts, and is suitable for construction equipment. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal bonding. If metal is inactive or cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Please consult the Active and Inactive Metal Table for specific application guidance.
$34.86
Hold It Australia T22 SCREWLOCK Low Strength for Easy Disassembly - 50ml Description: HOLDIT AUSTRALIA T22 Screwlock is a low strength, anaerobic thread locking compound, ideal for locking threaded fasteners that require disassembly with standard hand tools. It performs excellently on aluminium, steel, plated, stainless steel, and special alloy parts. T22 is characterized by its good temperature and solvent resistance. Applications T22 is specifically formulated to lock and seal small screws (less than ¼), including set screws with long engagement lengths. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal results. If the metal is inactive or the cure speed is too slow, apply HOLDIT AUSTRALIA AA471 Activator or HOLDIT AUSTRALIA AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow to fully cure before applying load. Properties of Uncured Material Chemical Type: Anaerobic Colour: Purple Toxicity: Low Solid Content: 100% Viscosity @ 25°C, cPs: 900-1,500 cps Specific Gravity: 1.05 Shelf Life: 24 months Performance of Cured Material Fixture Speed: 15-20 Min @ 22°C Full Cure: 24 Hours @ 22°C Temperature Range: -50°C to 150°C Product Conformity: MIL-S-46163A, ASTM D-5363, NSF Technical Datasheet The cure speed of HOLDIT AUSTRALIA T22 is dependent on temperature and substrate. The product shows a breakaway strength of 1Nm 9Nm on 3/8 plain steel nut & bolt after 1 hour and 5Nm 11Nm after 24 hours. On a 3/8 zinc nut & bolt, the strength is 1Nm 4Nm after 24 hours. Environmental and Fluid Resistance Heat Age: 100% retention in Engine oil @ 150°C Brake Fluid @ 150°C: 85% retention ATF @ 150°C: 85% retention 50/50 water/ethylene glycol @ 120°C: 80% retention Water @ 100°C: 80% retention Gasoline @ 25°C: 95% retention Diesel Fuel @ 25°C: 100% retention Ethyl Alcohol @ 25°C: 90% retention Active & Inactive Metal Table Category Cure Speed Metals Super Active Very Fast Cure Brass, Copper, Magnesium Active Fast Cure Iron, Steel, Nickel, Aluminium Inactive Slow Cure Stainless Steel, Titanium, Zinc Passive Primer Necessary Anodized Aluminium, Galvanised Steel, Ceramics, Glass, Plastics, Painted Finishes
$34.86
Prevent fasteners from loosening under vibration or temperature swings. Explore low, medium and high‑strength anaerobic threadlockers for serviceable and permanent assemblies. Great for automotive, machinery and DIY. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
