![Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240085.jpg?v=1754724137&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$26.50
![Sika Sikasil 670 Fire Resistant Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/7612895181462_fe2d5a8d-2a66-433f-9d24-2dfa9adec11a.jpg?v=1754711694&width=645)
SIKASIL® -670 FIRE | JOINT SEALANT Fire-rated joint sealant Up to 4 hours fire resistance according to EN 1366-4 Very good resistance to weathering Easy to smooth and very good workability DESCRIPTION Sikasil®-670 Fire is a fire-rated, 1-component, moisture-curing, low-modulus elastic joint sealant. USES Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates. CHARACTERISTICS / ADVANTAGES ▪ Up to 4 hours fire resistance according to EN 1366-4 ▪ Very good resistance to weathering ▪ Movement capability of ± 35% (ASTM C 719) ▪ Easy to smooth and very good workability ▪ Good adhesion to many different substrates ▪ Neutral curing ENVIRONMENTAL INFORMATION ▪ LEED® EQc 4.1 ▪ SCAQMD, Rule 1168 ▪ BAAQMD, Reg. 8, Rule 51 APPROVALS / STANDARDS ▪ EN 15651-1 F EXT-INT CC 25 LM ▪ EN 15651-4 PW INT ▪ ISO 11600 F 25 LM & G 25 LM ▪ ASTM C 920, class 35 ▪ EN 1366-4 assessment report ▪ ETAG 026 assessment report ▪ EN 13501-2 classification report ▪ EN 140-3 ▪ EN 13501-1 class B-s2-d0 PRODUCT INFORMATION Chemical Base Neutral cure silicone Colour: Grey Storage Conditions Sikasil®-670 Fire shall be stored in dry conditions, where it is protected from direct sunlight and at temperatures between +5 °C and +25 °C. Density 1.35 kg/l approx. (ISO 1183-1) TECHNICAL INFORMATION Shore A Hardness 16 approx. (after 28 days) (ISO 868) Secant Tensile Modulus 0.30 N/mm2 approx. at 100% elongation (23 °C) (ISO 8339) 0.50 N/mm2 approx. at 100% elongation (−20 °C) Elongation at Break 650% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Movement Capability ±25% (ISO 9047) ±35% (ASTM C 719) Service Temperature −40 °C to +150 °C Joint Design The joint width must be designed to suit the joint movement required and the movement capability of the sealant. The joint width shall be ≥ 10 mm and ≤ 40 mm. The joint depth shall be ≤ 20 mm. A width to depth ratio of 2:1 must be maintained (for exceptions, see table below). Backing Material Use polyethylene foam backing rods. Sag Flow 2 mm approx. (20 mm profile, 50 °C) (ISO 7390) Ambient Air Temperature +5 °C to +40 °C, min. 3 °C above dew point temperature Substrate Temperature +5 °C to +40 °C Curing Rate 2 mm/24 hours approx. (23 °C / 50% r.h.) (CQP 049-2) Skin Time 25 minutes approx. (23 °C / 50% r.h.) (CQP 019-1) Tooling Time 20 minutes approx. (23 °C / 50% r.h.) (CQP 019-2) APPLICATION INSTRUCTIONS SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikasil®-670 Fire adheres without primers and/or activators APPLICATION METHOD / TOOLS Sikasil®-670 Fire is supplied ready to use. After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a foil pack or cartridge into the sealant gun and extrude Sikasil®-670 Fire into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikasil®-670 Fire sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. CLEANING OF TOOLS Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® TopClean T. Once cured, residual material can only be removed mechanically. FURTHER DOCUMENTS ▪ Safety Data Sheet (SDS) ▪ EN 13501-2 classification report ▪ ETAG 026 assessment report ▪ Brochure Sika Fire Protection Solutions LIMITATIONS ▪ Sikasil®-670 Fire cannot be overpainted. Colour variations may occur due to exposure to chemicals, high temperatures and/or UV-radiation (especially with the colour shade white). However, a change in colour is purely of aesthetic nature and does not adversely influence the technical performance or durability of the product. ▪ Do not use Sikasil®-670 Fire on natural stone. Do not use Sikasil®-670 Fire on bituminous substrates, natural rubber, EPDM rubber or on any building materials which might bleed oils, plasticizers or solvents that could attack the sealant. ▪ Do not use Sikasil®-670 Fire to seal joints in and around swimming pools. ▪ Do not use Sikasil®-670 Fire for joints under water pressure or for permanent water immersion. ▪ Do not expose uncured Sikasil®-670 Fire to alcohol-containing products as this may interfere with the curing reaction.
$22.15
![Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324012236_d7a5d83c-0ea4-4a46-88bb-55e873bf5a05.jpg?v=1754711696&width=645)
Usage Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates. Advantages Up to 4 hours fire resistance according to AS 1530.4 Up to 4 hours fire resistance according to EN 1366-4 Very good resistance to weathering Movement capability of ± 35% (ASTM C 719) Easy to smooth and very good workability Good adhesion to many different substrates Neutral curing Colour Grey
$27.35
High-capacity foil sausages for low-waste, continuous application using a sausage gun. Great for long runs on façades, floors and roofing where efficiency matters. Select the right nozzle for joint size and movement. Use filters to refine by chemistry and cure profile. Always check the product page and TDS/SDS for set-up and usage instructions.
