In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Note :If you are working on a wooden floor, you will need to use the Fix-A-Floor Polyurethane For Loose, Squeaky Wood Flooring Repair. You can purchase it here.
Fix-A-Floor Repair Adhesive " Now Patented", is an Extra Strength Bonding Adhesive customized for the specific use of Re-Bonding loose and hollow tile, marble & stone without the expense and mess of removing or replacing them.
Fix-A-Floor is a simple do it yourself repair that is fast, easy and affordable not to mention fun and quite rewarding to anyone who can operate a drill, caulking gun and mix up a small batch of grout. Works on all sub-floor materials. Just Drill & Fill!
The TipThe Tip of the 10.1 oz. Fix-A-Floor tube has been specially designed and engineered with a pre-drilled 1/8" hole for the sole purpose of filling drilled holes in loose & hollow tile, marble & stone floors.
The Tip is extra firm and allows for a strong seal which promotes good flow and complete coverage. The 1/8" pre-drilled tip allows for use in narrow grout line applications or wider. It has marked lines showing clear cut points of 3/16", 1/4" or any other size you may need.
The AdhesiveFix-A-Floor Repair Adhesive is Strong & Flexible with elastomeric bonding properties to eliminate any future problems due to foundation settlement, expansion & contraction of the sub floor as well as poor original installation...
Used by professionals for years, now YOU can fix your loose & hollow, squeaky floors with Fix-A-Floor!!! Fix-A-Floor is Non-Toxic, Non-Flammable & Eco-Friendly!
Large problem area or small problem areas are no problem with Fix-A-Floor! Guaranteed for the life of your floor! Just Drill & Fill!
FAQs
Q: Will Fix-A-Floor work if I have heated floors?A: Yes! We have customers using Fix-A-Floor with heated floor elements all the time with no problems. Keep heating element off before, during & for 48 hrs. after applying. Q: Some of my grout is missing or completely gone? How can I use Fix-A-Floor?A: If bits and pieces of grout are missing here and there around the problem area, just go ahead and Drill & Fill, the adhesive will actually help to re-bond the bits that are cracking and loose. If your grout is completely gone we recommend lightly re-grouting the area allow to dry and then Drill & Fill! Q: Can I use Fix-A-Floor to fix my entire floor or just a small area?A: Fix-A-Floor works great on all size problem areas from 1 tile to the whole entire floor! Works on all types of Tile, Marble & Stone floors too! Q: Can I use Fix-A-Floor outside on my patio or deck?A: Yes! Fix-A-Floor works beautifully on interior and exterior applications. Q: Can I use Fix-A-Floor in my shower or Pool?A: No! Fix-A-Floor is not recommended for areas with exposed to excessive moisture. Q: Is Fix-A-Floor Safe?A: Yes! Fix-A-Floor is a non-toxic, non-flammable and Eco-Friendly water-based adhesive. Q: Can I use Fix-A-Floor to re-glue a tile that is off the floor?A: Yes, simply squeeze Fix-A-Floor onto the floor where the tile was and press the tile back down onto the floor, place weight and allow to dry for 24 hrs. Tile will be rebonded! Q: Do I have to place buckets of water on my floor after I Drill & Fill?A: It is recommended you place some kind of weight on the area to aid in curing and to be sure no excess adhesive is trapped under your floor before regrouting. It is not mandatory. Q: What if I don’t see the adhesive coming up out of the other holes?A: While filling Fix-A-Floor will usually come up and out of the other drilled holes. If this does not happen move to another hole and continue to fill, the adhesive is still travelling under the floor. If you see the adhesive coming back up out of the hole you are filling, be sure you are NOT pressing the tip of the tube down onto the subfloor. Q: What if the adhesive is clumpy or not flowing out of the tube properly?A: The adhesive in the tube has frozen either in transit during the cold winter months this can happen. Simply contact us for a replacement.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Get clean, precise application of glues, epoxies, resins, oils, inks, and other liquids with this easy to use 30 ml syringe and blunt tip fill needle. Ideal for workshop, craft room, electronics bench, and on site repair jobs where accuracy matters and mess is not an option.
Why you'll like it
Controlled dispensing for dots, lines, seams, and small cavities
30 ml capacity for longer runs without constant refilling
Graduated barrel with clear volume markings for repeatable dosing
Luer lock connection keeps the needle securely attached during use
Reusable barrel when used with compatible liquids and cleaned after use
Blunt tip needle for safe, non piercing filling and application
Common uses
Injecting Fix-A-Floor through grout lines to re bond hollow or loose tiles
Precision placement of two part epoxies and cyanoacrylate gels
Applying PVA wood glue into tight joints and dowel holes
Wicking thin adhesives along hairline cracks
Filling small voids and seams before clamping
Electronics work with flux, solder paste, and conformal coatings
Craft, model making, leatherwork, and jewellery repairs
Tile repair tip: A blunt tip of about 2 mm to 3 mm fits most grout lines. Drill a small hole in the grout as directed by the adhesive manufacturer, inject until the cavity is filled, then clean any squeeze out promptly.
What is included
1 × 30 ml syringe barrel with plunger
1 × blunt tip fill needle with luer lock hub
1 × protective cap for storage
Specs
Capacity
30 ml
Connection
Luer lock
Needle style
Blunt tip, non piercing
Barrel material
Transparent polypropylene
Plunger seal
Latex free elastomer
Use
For adhesives and shop liquids only, not for medical use
How to use
Attach the blunt tip needle by twisting it onto the luer lock until snug.
Pull back the plunger, draw in your adhesive, then tap the barrel to release trapped air.
Dispense with slow, steady pressure for consistent beads and dots.
For Fix-A-Floor, inject through the grout holes until filled and follow the cure steps on the product label.
After use, expel remaining liquid if suitable, then flush the barrel and needle using a cleaner compatible with your adhesive.
Dry completely and cap for storage.
Compatibility tips
Works well with PVA, polyurethane, epoxy, acrylic, latex, and many hobby liquids.
For solvent based products, confirm compatibility with polypropylene before use.
Do not store reactive two part mixes inside the syringe after they begin to cure.
Safety
Not sterile and not for medical, food, or body use.
Wear gloves and eye protection when handling chemicals.
Keep out of reach of children.
FAQ
Can I reuse itYes, if your adhesive and cleaner are compatible with polypropylene and the luer lock needle. Clean immediately after use for best results.
Will it work with thick glueYes, but very thick products may require more pressure and a wider blunt tip size.
Does it come sterileNo. This set is for industrial, workshop, and hobby applications only.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
3M™ Panel Bonding Adhesive (PN 08116) is a two-part epoxy designed to bond non-structural outer body sheet metal such as, but not limited to, quarter panels, roof panels, van sides, box sides and door skins
Product Uses Bonding steel, aluminum, SMC and FRP (fiberglass) to themselves or each other.
Use with the following applicators: PN08117 (manual), PN 09930
(pneumatic). 3M™ Mixing Nozzle, PN 08193 (6/bag), PN 08194 (50/box).
For professional use only. Not intended for retail sale.
The following times have been determined with ambient air temperature and
substrate temperature @ 70°F and are considered typical values.
WORK TIME:
90-120 minutes
CLAMP TIME
6 hours
CURE TIME:
24 hours
SURFACE PREPARATION:
1. Wash surface with soap and water to remove water soluble contaminants. Follow the soap and water wash with an appropriate VOC compliant product for removal of surface contaminants.
2. Remove all rust, primer and paint from the areas to be bonded or welded using a Scotch-Brite™ Clean & Strip Disc or 3M grade 50 Grinding Disc.
3. Straighten all metal, and “dry-fit” the parts.
4. Clamp the part in place and check for fit and alignment.
5. Remove the panel from the vehicle. All areas to be welded should be coated with 3M™ Weld-Thru II Coating (PN 05917) according to the directions on the can. Adhesive should not be applied to these areas.
PRODUCT PREPARATION:
6. Place an adhesive cartridge in the applicator gun.
7. Remove the retaining collar and plug from the end of the cartridge. Discard plug, but save the retaining collar.
8. Before attaching a nozzle, “equalize” the cartridge by dispensing just enough product to be sure that both parts A and B are present at the outlet.
9. Attach a 3M™ Static Mixing Nozzle to the cartridge and lock in place with the retaining collar.
10. Dispense a small amount of material through the mixing nozzle onto a disposable surface and discard.
11. Apply an adhesive bead to all bare metal surfaces of both pieces to be bonded. Using a plastic spreader or acid brush, tool out the adhesive to cover all bare metal surfaces.
12. Apply a 1/8" diameter adhesive bead approximately 1/4" from the inside edge of the replacement panel.
• Quarter Panels: Adhesive should be applied to the lower edge, the wheel opening, the door jamb areas of the quarter, and at the factory seam of the sail
panel. 3M suggests that the rear vertical portion of a quarter panel should be welded. It is acceptable to bond the rear vertical portion of a quarter panel, if recommended by the OEM. Additionally, most OEM’s only recommend full panel replacement. Should you perform a belt cut on a sail panel, 3M recommends welding the belt cut to ensure optimal cosmetic appearance. All areas to be welded should be sprayed with 3M™ Weld-Thru II (PN 05917).
Do not apply adhesive to these areas.
• Roof Panels: Adhesive should be applied around the perimeter of the roof anel. To replace the factory-applied NVH foam/spacer between the roof bow and the roof panel, use one of the following: 3M™ Urethane Seam Sealer (PN 08360, PN 08361 or PN 08364), 3M™ MSP Seam Sealer (PN 08369 or
PN 08370), or 3M™ NVH Dampening Material (PN 04274) to the roof bows as needed.
• Door Skins: Adhesive should be applied to the hem flange area. To replace the factory-applied NVH foam/spacer between the intrusion beam/s and the
door skin, use one of the following: 3M™ Urethane Seam Sealer (PN 08360, PN08361 or PN 08364), 3M™ MSP Seam Sealer (PN 08369 or PN 08370),
or 3M™ NVH Dampening Material (PN 04274) to the intrusion beam/s as needed.
13. Clamp the panel in its proper position.
14. Tool any adhesive “squeeze out” to seal the outside of the seam all along the bonded edge of the panel.
• Caution: The adhesive is combustible. Keep any MIG welding a minimum of two inches from the adhesive. As with any welding operation, keep the appropriate fire extinguisher within reach, and be alert to any smoke or flame that may be present. Resistance spot welding through uncured adhesive is
acceptable.
15. Spray the inside of quarter panels, interior cavities, and any welded seams with 3M™ Rust Fighter-I (PN 08891 or PN 08892).
16. Clamps may be removed after six hours at 73°F. Parts will need to remain clamped longer if the temperature is below 73°F and/or if there is any tension
on the part. The cure time may be accelerated by applying heat with a heat gun or lamps.
17. Allow 24 hours at a minimum of 73°F before returning vehicle to service.
CLEAN-UP: Unmixed material may be cleaned from most surfaces with an appropriate VOC compliant product.
Storage and Handling When stored at the recommended conditions in original, unopened containers, this product has a shelf life of 24 months from the date of manufacture. Store at room temperature. Rotate stock on a “first-in-first-out” basis. After use, leave the mix nozzle in place to seal the cartridge.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Quickly bonds to primer, metal, fiberglass and aluminum
Two-part component formula delivers excellent durability and less shrinkage
Quickly repairs paint scratches, minor dents and stone chips
Good spreading properties allow for ease of use
Specifications
Application Dent Fill
Brand Bondo®
Color White, Off white
Product Type Glaze Putty
Substrate Aluminum, eCoat or Paint, Galvanized, SMC
Details
Quickly bonds to primer, metal, fiberglass and aluminum
Two-part component formula delivers excellent durability and less shrinkage
Quickly repairs paint scratches, minor dents and stone chips
Good spreading properties allow for ease of use
Fast curing makes putty sandable in only 20 minutes
Putty is compatible with all types of automotive paint systems
Use during the Fill stage of the 3M™ Body Repair System
Bondo® Professional Glazing & Spot Putty smooths and repairs pin holes, scratches, nicks, minor dents, stone chips and other surface imperfections in automotive paint and bodies. This product is a 2-part component formula that securely and quickly bonds to primer, metal, fiberglass and aluminum.
Professional Quality Surface Blemish Repairs
Bondo® Professional Glazing & Spot Putty quickly repairs paint scratches, minor dents and stone chips. Our professional quality formula comes as a two-part product with putty and cream hardener to produce a mixture that won't shrink once cured. This glazing and spot putty has a 5-minute working time and a 20-minute curing time, giving you the perfect balance of enough time to complete the repair with a fast cure that keeps your project moving forward on schedule.
Perfect Repairs Every Time
Once cured, you're ready to sand to create a smooth patch that matches the surrounding surface beautifully. Our repair putty securely bonds to primer, metal, fiberglass and aluminum, and it resists gumming up sandpaper and shrinking. It can be used with all types of paint systems for professional-looking results.
Use During the Fill Stage of the 3M™ Body Repair System
Even a small repair can seem complex at first. So 3M's Body Repair System simplifies the entire automotive body repair process by dividing it into four stages:
Stage 1 — Prepare. This stage includes pulling dents, removal of paint and rust and efficient, effective masking of the area.
Stage 2 — Fill. This stage involves patching holes with reinforced filler and smoothing and shaping filler before painting.
Stage 3 — Paint. This stage includes painting the area and blending and smoothing primer and paint.
Stage 4 — Finish. The final stage for showroom-grade results: removing small defects, sealing and polishing clear coats and other painted surfaces.
3M supplies premium products such as abrasives, tapes, body fillers and tools for every stage. This system helps you work easily, efficiently and successfully across the entire body repair process.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done.
HARDENED STEEL - Claws lock into drywall anywhere.
PROVEN HOLD - Trusted strength up to 45 pounds
NO TOOLS – just push in with your thumbs
NO STUDS – Hang anywhere on drywall
NO REGRETS – No big holes left in your walls
NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger
AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done.
HARDENED STEEL - Claws lock into drywall anywhere.
PROVEN HOLD - Trusted strength up to 45 pounds
NO TOOLS – just push in with your thumbs
NO STUDS – Hang anywhere on drywall
NO REGRETS – No big holes left in your walls
NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger
AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done.
HARDENED STEEL - Claws lock into drywall anywhere.
PROVEN HOLD - Trusted strength up to 45 pounds
NO TOOLS – just push in with your thumbs
NO STUDS – Hang anywhere on drywall
NO REGRETS – No big holes left in your walls
NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger
AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done.
HARDENED STEEL - Claws lock into drywall anywhere.
PROVEN HOLD - Trusted strength up to 45 pounds
NO TOOLS – just push in with your thumbs
NO STUDS – Hang anywhere on drywall
NO REGRETS – No big holes left in your walls
NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger
AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done.
HARDENED STEEL - Claws lock into drywall anywhere.
PROVEN HOLD - Trusted strength up to 45 pounds
NO TOOLS – just push in with your thumbs
NO STUDS – Hang anywhere on drywall
NO REGRETS – No big holes left in your walls
NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger
AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done.
HARDENED STEEL - Claws lock into drywall anywhere.
PROVEN HOLD - Trusted strength up to 45 pounds
NO TOOLS – just push in with your thumbs
NO STUDS – Hang anywhere on drywall
NO REGRETS – No big holes left in your walls
NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger
AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25, 45 & 65 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done.
HARDENED STEEL - Claws lock into drywall anywhere.
PROVEN HOLD - Trusted strength up to 45 pounds
NO TOOLS – just push in with your thumbs
NO STUDS – Hang anywhere on drywall
NO REGRETS – No big holes left in your walls
NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger
AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Let cords be a thing of the past! Command™ Cord Management products allow you to better organise and keep your home or office space free from the mess and tangled clutter.
No more dangerous, tangled cords behind your computers, appliances and entertainment centres! Command™ Cord Organisers are perfect for work and home offices, as well as entertainment areas, where they keep cords organised and safely out of the way.
Holds up to 900g
Damage-Free Hanging
Easy to hang - no tools required!
Holds strongly and removes cleanly
Works on a variety of indoor surfaces, such as painted Gyprock, finished wood, tile, metal and glass
Ideal for hanging and organising extension cords
Prevents trip hazards
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Can I use Command™ Products on glass windows?
It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging.
Will Command™ Products stick to brick?
No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings).
Can I use Command™ Products on fresh paint?
Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint.
Can I use Command™ Products on wallpaper?
No. Most wallpapers are too delicate and can tear when adhesives are applied.
Will it hold soundproofing acoustic foam board or decorative plates?
Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Can I use Command™ Products on glass windows?
It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging.
Will Command™ Products stick to brick?
No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings).
Can I use Command™ Products on fresh paint?
Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint.
Can I use Command™ Products on wallpaper?
No. Most wallpapers are too delicate and can tear when adhesives are applied.
Will it hold soundproofing acoustic foam board or decorative plates?
Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Can I use Command™ Products on glass windows?
It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging.
Will Command™ Products stick to brick?
No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings).
Can I use Command™ Products on fresh paint?
Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint.
Can I use Command™ Products on wallpaper?
No. Most wallpapers are too delicate and can tear when adhesives are applied.
Will it hold soundproofing acoustic foam board or decorative plates?
Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Can I use Command™ Products on glass windows?
It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging.
Will Command™ Products stick to brick?
No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings).
Can I use Command™ Products on fresh paint?
Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint.
Can I use Command™ Products on wallpaper?
No. Most wallpapers are too delicate and can tear when adhesives are applied.
Will it hold soundproofing acoustic foam board or decorative plates?
Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Can I use Command™ Products on glass windows?
It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging.
Will Command™ Products stick to brick?
No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings).
Can I use Command™ Products on fresh paint?
Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint.
Can I use Command™ Products on wallpaper?
No. Most wallpapers are too delicate and can tear when adhesives are applied.
Will it hold soundproofing acoustic foam board or decorative plates?
Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Can I use Command™ Products on glass windows?
It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging.
Will Command™ Products stick to brick?
No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings).
Can I use Command™ Products on fresh paint?
Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint.
Can I use Command™ Products on wallpaper?
No. Most wallpapers are too delicate and can tear when adhesives are applied.
Will it hold soundproofing acoustic foam board or decorative plates?
Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
3M™ Marine Adhesive Sealant 5200 is extremely strong and retains its strength above or below the water line. Stays flexible too - allows for structural movement. Has excellent resistance to weathering and salt water.
Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fibreglass deck to fibreglass hull, wood to fibreglass, portholes and deck fittings, motors on fibreglass transoms, under mouldings, hull seams above and below the water line. Centreboard trunk joints. Between struts and planking. Stern joints. Deck housing, etc. Easy to apply with a manual caulking gun. Won't sag or flow in vertical or horizontal seams.
Very high strength
Watertight bonds
Above/Below waterline use
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
3M™ Marine Adhesive Sealant 5200 is extremely strong and retains its strength above or below water line. Stays flexible too - allows for structural movement. Has excellent resistance to weathering and salt water.
Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fibreglass deck to fibreglass hull, wood to fibreglass, portholes and deck fittings, motors on fibreglass transoms, under mouldings, hull seams above and below water line. Centre board trunk joints. Between struts and planking. Stern joints. Deck housing, etc. Easy to apply with manual caulking gun. Won't sag or flow in vertical or horizontal seams.
Very high strength
Watertight bonds
Above/Below waterline use
Specifications
Adhesive Type Polyurethane
Application Method Hand or pressure caulk
Brand 3M™
Colour White
Consumer Label Yes
Cure Time 24 Hours
Full Cure 3mm per 5 day
Hardness 68 Shore A
Industries Marine
Physical Form Medium paste
Product Form Cartridge
Solids Weight Percent (Approximate) 97 Percent
Tack Free Time 12 Hour
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
3M™ Marine Adhesive Sealant 5200 is extremely strong and retains its strength above or below water line. Stays flexible too - allows for structural movement. Has excellent resistance to weathering and salt water.
Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fibreglass deck to fibreglass hull, wood to fibreglass, portholes and deck fittings, motors on fibreglass transoms, under mouldings, hull seams above and below water line. Centre board trunk joints. Between struts and planking. Stern joints. Deck housing, etc. Easy to apply with manual caulking gun. Won't sag or flow in vertical or horizontal seams.
Very high strength
Watertight bonds
Above/Below waterline use
Specifications
Adhesive Type Polyurethane
Application Method Hand or pressure caulk
Brand 3M™
Colour White
Consumer Label Yes
Cure Time 24 Hours
Full Cure 3mm per 5 day
Hardness 68 Shore A
Industries Marine
Physical Form Medium paste
Product Form Cartridge
Solids Weight Percent (Approximate) 97 Percent
Tack Free Time 12 Hour
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
3M™ Marine Adhesive Sealant 5200 is extremely strong and retains its strength above or below the water line. Stays flexible too - allows for structural movement. Has excellent resistance to weathering and salt water.
Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fibreglass deck to fibreglass hull, wood to fibreglass, portholes and deck fittings, motors on fibreglass transoms, under mouldings, hull seams above and below the water line. Centreboard trunk joints. Between struts and planking. Stern joints. Deck housing, etc. Easy to apply with a manual caulking gun. Won't sag or flow in vertical or horizontal seams.
Very high strength
Watertight bonds
Above/Below waterline use
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Agnews Water Putty - Hard-Setting Filler for Wood, Plasterboard, Concrete & More
Agnews Water Putty is a professional, powder-based repair and levelling compound for durable, long-lasting results. Mix only what you need with clean water, then patch, level or rebuild surfaces with confidence. Once cured, it sets rock hard, bonds permanently, and can be sawn, drilled and sanded to a smooth, paint-ready finish.
Key features
Brand: Agnews
Unlimited shelf life when stored dry
Non cracking, non shrinking, non sinking
Won't fall out – adheres firmly and fills to any depth
Interior & exterior grade (seal exterior applications after full dry)
Non flammable and no VOCs
Mix what you need for minimal waste
Suitable substrates
Plasterboard, concrete, wood/timber, cement sheet, masonry. Also suitable for minor floor levelling and feathering on concrete, timber and ceramic tile substrates.
Typical applications
Fill holes in wood: knotholes, nail and screw holes, dents, edge build-ups
Wall patching: cracks and cavities in plasterboard and cement sheet
Furniture repair: tighten loose joints, reset fasteners, rebuild profiles
Floor levelling: ramp or smooth minor level variations before floor coverings
Trim and fixtures: refit loose door bumpers and trims with reliable hold
Architectural & hobby moulding: casting and shaping durable components
Why choose Agnews
Agnews Water Putty cures to a dense, stone-hard finish that resists shrinkage and cracking even in deep fills. It bonds securely, stays put, and finishes cleanly, delivering a stable base for sanding, priming and painting. From small touch-ups to larger restorations, it provides consistent, professional results.
Directions (general guide)
Surface prep: Ensure the area is clean, dry, sound and free of dust, oil or loose material. For very porous substrates, lightly dampen to reduce rapid suction.
Mix: Add powder to clean water and blend to a smooth, lump-free paste. Adjust water to suit application (thicker for filling, looser for fairing/skim).
Apply: Press firmly into cracks or voids with a putty knife or trowel. Overfill slightly so you can sand back flush.
Cure: Allow to dry thoroughly. Dry time varies with thickness, temperature and humidity.
Finish: Sand to profile. Prime and paint or seal. For exterior applications, always seal after full dry.
Exterior use guidance
This is a hard-setting, non-flexible compound. For exterior use, only apply over stable substrates with minimal expansion and contraction from temperature changes. Ensure the putty is fully dry before sealing with a suitable exterior-grade coating.
Finishing & compatibility
Paintable and sealable after full dry; prime as required for best results.
Can be cut, carved, drilled and sanded after cure without crumbling.
For stained timber finishes, test a small area first for colour and absorption.
Pro tips
Mix small batches and use promptly.
For deep voids, apply in layers if needed, allowing each layer to firm before the next.
Store powder in a cool, dry place to maintain its unlimited shelf life.
Clean tools with water before material cures.
At a glance
Substrates: plasterboard, concrete, wood/timber, cement sheet, masonry
Uses: patching, levelling, rebuilding, moulding
Properties: non cracking, non shrinking, non sinking, non flammable, no VOCs
Finish: hard, dense, smooth and paint-ready after sanding/priming
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
An adhesive for general woodworking applications. It is also ideal for Art and Craft applications and school supplies. Great to make slime. Ideal to bond paper wood, ceramic, porcelain and fabrics.
Boyle PVA glue is suitable for porous surfaces such as wood, laminated board, leather, textiles, cork, paper, felt, styrene foam, cardboard, paper mache, decoupage collage, fabric flowers and more.
Non-toxic
Dries clear
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys All Fix Big Jobs is a convenient all-rounder adhesive that sticks just about anything to anything. It provides virtually instant grab on dry porous surfaces eliminating the need for nails and screws on many jobs. It is a heavy-duty adhesive that will bond a wide variety of materials, has low fumes, and conveniently cleans up with water.
Features
Fast - virtually instant grab on dry porous surfaces eliminates the need for nails and screws on many jobs
Fast grab minimises the need for clamping
Strong - Heavy-duty adhesive that will bond a wide variety of materials
Safe - Low odour, low fumes and non-flammable
Dries white and is able to be painted over once dry
Lots of working time - bonds can be repositioned within 5-10 minutes
Easy to use
Fills minor gaps in uneven surfaces (bridges gaps up to 9mm)
Strong bond on porous surfaces after 24 hours, cures to maximum strength over a few days
Where can this product be used?
Re-adhering carpet
House numbers to brickwork
Wooden furniture repairs
Repairing damaged plasterboard
Building a dog house
Skirting boards
Attaching architraves
Attaching wall panelling
Attaching chair (dado) rails
Attaching or building a shelf
Use for larger interior projects
What materials is this product suitable for?
Plasterboard
Cabinet
Plaster coving
Carpet
Wood
Particleboard
Metals (other surface must be porous)
Glass (other surface must be porous)
Ceramics (other surface must be porous)
Brick (other surface must be porous)
Concrete
Cork
Polystyrene foam (other surface must be porous)
UPVC (other surface must be porous)
Many rigid plastics* (other surface must be porous)
Loose wall tiles (in non-wet areas)
How to Use
Surfaces to be bonded must be dry, sound and free from grease/oil and dust.
Work tube between fingers for several seconds to loosen contents. Cut the tip of the nozzle and squeeze to apply adhesive onto one surface.
Immediately press parts firmly together. Bonds can be repositioned for up to 5 minutes. If adhesive surfaces form a skin no bond will form. The bond will usually have good strength after 24 hours and will continue to strengthen for a few days.
Application Tips
For long narrow attachments (e.g. skirting boards) apply one or two continuous beads.
For larger flat areas use beads approximately 30cm apart.
For small items (e.g. tiles) spots of adhesive may be used.
Wipe away excess adhesive with a damp cloth. Dried adhesive is best removed by scraping.
Limitations:
Not suitable for permanently wet or damp areas.
Not suitable for fixing mirrors. Use Selleys Liquid Nails Mirror Metal & Glass.
*Not suitable for polyethylene and polypropylene. Use Selleys All Plastic Fix.
Bonds are not water-resistant. Protect bonds from water penetration if used in exterior applications.
Not resistant to strong acids and strong organic solvents.
Do not apply below 10°C.
When used near brass or copper, the immediate area of contact will discolour to a blue tone.
Handy Tips
At least one surface must be porous for effective bonding. If both surfaces are non-porous, drying time is greatly increased.
Clamping may be necessary until adhesive dries.
Wet, damp and cold weather will increase drying time
Wipe away excess with a damp rag.
Use temporary supports when bonding a heavy load - support until adhesive dries. Particularly on uneven or smooth or non-porous surfaces.
Good for gap filling - i.e. sticking two rough surfaces together.
All Fix Big Jobs may stain slightly and colour can be paler than the surrounding area, squeeze out should be wiped off if intending to stain.
Clean Up
Uncured product may be removed with water.
Cured product can be removed by scraping.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys All Fix Multi Grip is a strong multipurpose adhesive that dries clear it is ideal for hobby projects or repair of household items and PVC pool liners.
FeaturesMultipurposeDries Clear for a seamless bondStrongFlexibleSafe to use indoors and outsideSolvent based adhesive
Where can this product be used?Hobby projectsRepairs of household itemsPVC pool liners
What materials is this product suitable for?WoodMetalGlassCeramicBrickConcreteCorkMost plastics*
How to use this productUse in a well ventilated areas.
Ensure surfaces are clean and dry. Remove cap and carefully pierce foil seal with sharp object. Replace nozzle part of cap.Squeezing gently, apply an even coating of Selleys All Fix to both surfaces to be joined. Press surfaces together and clamp or hold firmly for approximately 1-2 minutes or until adhesive grabs. Instant bonds can be achieved on contact by waiting approximately 1 minute before pressing parts together firmly.Allow approximately 10-12 hours drying to achieve strength sufficient for normal use. Maximum bond strength is achieved after 24 hours or longer if large areas or nonporous materials (e.g. PVC) are being bonded.After application, clean nozzle and replace cap. Any spills can be removed with acetone (found in some nail polish removers).
Clean UpUncured product may be removed with waterCured product can be removed by scraping
Handy tipsFor very porous surfaces – apply a thin coat to both surfaces and allow to dry (approximately 5 minutes). Apply another layer as per normal directions.
Limitations*Not suitable for polyethylene and polypropylene – use Selleys All Plastic FixNot suitable for polystyrene foam – use All Fix Big JobsNot for bonding requiring heat resistance above 90°C – use Quick Fix Ultra RepairSafety tipsDo not swallowAvoid contact with skin and eyes and breathing vapourRemove from skin with soap and waterIf in eyes, hold eyes open, flush with plenty of water for 15 minutes and seek medical attentionHighly flammable, keep away from sources of ignitionFor advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764766) or a doctorFor further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site
Storage and re-useLeave nozzle on tightly if storing once opened
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A two-component epoxy formula highly concentrated with carefully selected pure aluminium particles, modified curing agents, and special high quality additives to provide maximum strength, durability, and ease of application.
APPLICATIONS: ALUMBOND is specially formulated for repairing HVAC copper pipes, HVAC condenser coils, tanks, valves, pumps, castings, water jackets, radiators, etc., where non-rusting, non-magnetic aluminum finish is desired.
PHYSICAL PROPERTIES:
Color Grey
Pot Life 1 lb. @ 24ºC (75°F) 45 minutes
Viscosity Non-sagging Paste
Mixed Viscosity 330,000 cps
Cure Shrinkage 0.0005 in/in
Temperature Resistance 250°F (121ºC)
Hardness (Shore, ASTM D 1706) 83D
Cured Density 17.5 cu. in. per lb.
Coefficient of Thermal Expansion 40 X 10- 6 cm/cm/ºC
Compression Strength (ASTM D 695) 8,600 psi (59 M Pa)
Tensile Strength (ASTM D 638) 3,500 psi (24 M Pa)
Maximum Line Pressure (after 5 hours application time) 650 psi
DIRECTIONS: Surfaces must be clean, dry, and preferably roughened for maximum adhesion.
Dispense equal volumes of resin and hardener. Volume Ratio is 1:1.
Mix thoroughly for 6 minutes making certain that all of the hardener comes in contact with all of the resin.
Apply the mixed compound with a putty knife, spatula, or similar tool. The tool may be moistened with water to provide a smooth finish to the HY-POXY ALUMBOND.
CURING TIME: At 75°F (24°C) a ½” (12.5mm) layer of HY-POXY ALUMBOND putty will be hard in approximately 45 minutes
HY-POXY ALUMBOND will not cure properly below 40°F (4°C).
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding
Features
Super Durable
High Strength
100% waterproof* – *(not for permanent water immersion)
Bonds wood to almost anything
Acid & chemical Resistant – PVA’s break down with acid/alkaline contact
Versatile can be used to bond surfaces other than wood
Heat resistant up to 140 deg
Generous working time (10 minutes)
Expands as it dries
Sandable – easy, will not clog sandpaper like other PVA emulsion glues
Paintable
Stainable after sanding
The product is a brown liquid and turns a light yellow when fully cured
Can be used for gap filling
Can Also be used to bond surfaces other than wood I.e metal to metal
Bonds MDF
Non-Toxic (once fully cured)
Where can this product be used?
Interior and exterior
Sauna or cabinet repairs in high heat areas
Bonding Timber to other surfaces (metal etc)
Cubby House with metal roof & floor lining
Planter boxes
Steps leading off a verandah
Timber letterbox to a metal support frame
Window frame
Decorative timber to a pergola
Interior panels of a boat
Repairing wooden boat oars
Repairing wooden handles on tools
Timber joinery
Laminating chopping boards
Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice)
Cannot be used if application temperature is below 5°C
For best results, one surface should be porous
Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua
Not recommended for structural applications
Not recommended for vertical projects due to runny consistency
While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming
Surfaces should be clamped tightly or weighted
What materials is this product suitable for?
MDF
Glass
Metal
Concrete
Ceramic
Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first).
All timbers
How to use this product
Surfaces to be bonded must be close fitting, clean, dust and grease free.
Wipe very dry porous surfaces with a damp cloth 1 minute before bonding.
Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures.
Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured.
Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container).
Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting.
Clean tools with acetone or white turpetine immediatly after use (before adhesive dries).
Handy tips
1L covers approx. 8m2
It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin).
For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface.
The tighter you clamp, the better bond you will obtain (as Durabond expands).
Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.)
Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive.
In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet.
It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin.
If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off.
Safety tips
Contains organic isocyanate polymers.
On contact, uncured adhesive can irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water.
Avoid breathing vapours. Ensure use in a well-ventilated area. Product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
Warning: this product contains organic isocyanate polymers. This product has been classified as hazardous according to the criteria of NOHSC and HSNO. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and re-use
Clean tools with acetone or white spirit immediately after use (before adhesive dried).
Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact.
It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Industrial grade PVA, especially developed for use by professional woodworkers and craftsmen, for large projects. Off-white in colour, drying to a light coloured clear film.
Features
Excellent performance properties for repairs or building projects
No mixing required
Suitable for exterior use in non-structural applications
Heat resistant to 110°C (bonds will not weaken in exposure to direct summer sun)
Can be chiselled, routed or turned
Suitable for end grain gluing – won’t stain timber, cream in colour, but dries clear with a slight yellow tint
Non-toxic
Sandable – will not clog sandpaper like other PVA emulsion glues
More water resistant than Aquadhere interior
Has a higher heat resistance than Aquadhere interior
Paintable
Provides a stronger bond than Aquadhere interior for larger jobs
Bonds MDF
Weather resistant
Cleans up with water
Where can this product be used?
Cabinet and furniture making
Timber letterbox
Making a bookshelf
Restoring furniture
Gluing cupboard shelves for additional support
Repairing a door frame or window
Repairing or building wooden outdoor furniture
Indoor furniture
Storage chest for tools
Pot plant stand
Dog kennel
Bed heads
Timber joinery
Wooden toys
Unsuitable for use on coated wallpaper overlaps eg vinyl
Will not take common timber stains
Not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue
Not suitable for below waterline applications or continuous submersion. We recommend Selleys Knead It Aqua for these situations.
What materials is this product suitable for?
Softwoods
Plywood
Joinery
Hardwoods
MDF
Laminating
Particleboard
Dowelling
Veneering
Chipboard
How to use this product
Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease.
Shake bottle before use
Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours.
Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood.
Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers.
Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft.
Cure slows significantly in humid, cold conditions.
Handy tips
1L covers approx. 5m2
To fill small gaps, Aquadhere can be mixed with sawdust.
Longer clamping times may be required for joints under high stress, or alternatively use 308 High Stress Wood Glue.
Avoid contaminating Aquadhere Exterior with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods.
Painting or varnishing constructions made of porous softwoods will improve the resistance of bonds to water exposure.
On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond.
If you are gluing over a larger surface, try using a small roller to aid in application.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of Selleys Hand Kleen Wipes nearby for a quick and effective cleanup.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Industrial grade PVA, especially developed for use by professional woodworkers and craftsmen, for large projects. Off-white in colour, drying to a light coloured clear film.
Features
Excellent performance properties for repairs or building projects
No mixing required
Suitable for exterior use in non-structural applications
Heat resistant to 110°C (bonds will not weaken in exposure to direct summer sun)
Can be chiselled, routed or turned
Suitable for end grain gluing – won’t stain timber, cream in colour, but dries clear with a slight yellow tint
Non-toxic
Sandable – will not clog sandpaper like other PVA emulsion glues
More water resistant than Aquadhere interior
Has a higher heat resistance than Aquadhere interior
Paintable
Provides a stronger bond than Aquadhere interior for larger jobs
Bonds MDF
Weather resistant
Cleans up with water
Where can this product be used?
Cabinet and furniture making
Timber letterbox
Making a bookshelf
Restoring furniture
Gluing cupboard shelves for additional support
Repairing a door frame or window
Repairing or building wooden outdoor furniture
Indoor furniture
Storage chest for tools
Pot plant stand
Dog kennel
Bed heads
Timber joinery
Wooden toys
Unsuitable for use on coated wallpaper overlaps eg vinyl
Will not take common timber stains
Not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue
Not suitable for below waterline applications or continuous submersion. We recommend Selleys Knead It Aqua for these situations.
What materials is this product suitable for?
Softwoods
Plywood
Joinery
Hardwoods
MDF
Laminating
Particleboard
Dowelling
Veneering
Chipboard
How to use this product
Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease.
Shake bottle before use
Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours.
Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood.
Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers.
Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft.
Cure slows significantly in humid, cold conditions.
Handy tips
1L covers approx. 5m2
To fill small gaps, Aquadhere can be mixed with sawdust.
Longer clamping times may be required for joints under high stress, or alternatively use 308 High Stress Wood Glue.
Avoid contaminating Aquadhere Exterior with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods.
Painting or varnishing constructions made of porous softwoods will improve the resistance of bonds to water exposure.
On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond.
If you are gluing over a larger surface, try using a small roller to aid in application.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of Selleys Hand Kleen Wipes nearby for a quick and effective cleanup.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water.
Features
No mixing required – Ready to use straight from the pack
Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear.
Non-toxic
Dries Clear
Cleans up with water
Where can this product be used?
School projects and craft
Furniture repairs
Repair a split trim
Fix a broken photo frame
Restoring furniture
Fix a wobbly chair
Gluing cupboard shelves for additional support
Repairing a door frame or window
Fix a wine rack
Re-attach book cover/spine or repair torn bindings
Fix a broken drawer
Wooden toy repairs
Craft projects
Unsuitable for use on coated wallpaper overlaps eg vinyl
Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond).
Will not take common timber stains
Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue.
Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable.
Will not bond MDF, we recommend using Aquadhere Exterior
What materials is this product suitable for?
End grain gluing
Craftwork
Cloth
Paper
Mosaics
Leather
Other craft materials
How to use this product
Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease.
Shake bottle before use
Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours.
Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood.
Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers.
Cure slows significantly in humid, cold conditions.
Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft.
Handy tips
1L covers approx. 8m2
To fill small gaps, Aquadhere can be mixed with sawdust.
Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High Stress Wood Glue.
Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods.
On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond
Cured adhesive can be resoftened by prolonged contact with hot water or steam.
Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing.
If you are gluing over a larger surface, try using a small roller to aid in application.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Safety tips
Aquadhere is considered a non-hazardous material.
In case of eye contact, hold eye open and flush with plenty of water for 15 minutes.
Storage and re-use
For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours.
Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Quick setting in 5 minutes
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling (surfaces need not mate closely)
Good chemical resistance
Appearance
Clear with a slight yellow tinge
Where can this product be used?
Bakelite – joining or repairing
Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots
Repairing splits or cracks in a tennis racket
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Rigid Plastic
Crystal
Leather
How to use this product
General Use
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately.
When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden.
To use Selleys Araldite Singles:
Fold – the pack in half, so that foil is back to back.
Tear – carefully along perforations.
Squeeze – bubbles to extrude adhesive.
Mix – two parts together until well combined.
Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes.
Handy tips
For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping is recommended for a stronger bond.
Singles are great for those unexpected household breakages, so keep them at home, just in case.
Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
Safety tips
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Do not use solvents near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non toxic when set.
For further information refer to the Material Safety Data Sheet (MSDS).
Storage and re-use
Ensure caps are replaced and product stored in a cool dry place.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours.
Features:
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Quick setting in 5 minutes
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling (surfaces need not mate closely)
Good chemical resistance
Appearance:
Clear with a slight yellow tinge
Where can this product be used?
Bakelite – joining or repairing
Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots
Repairing splits or cracks in a tennis racket
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Rigid Plastic
Crystal
Leather
How to use this product:
General Use
-Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
-All traces of grease, rust paint, etc. should be removed.
-For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
-Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick.
Safety tips:
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Do not use solvents near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non toxic when set.
For further information refer to the Material Safety Data Sheet (MSDS).
Storage and re-use
Ensure caps are replaced and product stored in a cool dry place.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours.
Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Quick setting in 5 minutes
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling (surfaces need not mate closely)
Good chemical resistance
Appearance
Clear with a slight yellow tinge
Where can this product be used?
Bakelite – joining or repairing
Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots
Repairing splits or cracks in a tennis racket
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Rigid Plastic
Crystal
Leather
How to use this product
General Use
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately.
When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden.
To use Selleys Araldite Singles:
Fold – the pack in half, so that foil is back to back.
Tear – carefully along perforations.
Squeeze – bubbles to extrude adhesive.
Mix – two parts together until well combined.
Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes.
Handy tips
For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping is recommended for a stronger bond.
Singles are great for those unexpected household breakages, so keep them at home, just in case.
Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
Safety tips
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Do not use solvents near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non toxic when set.
For further information refer to the Material Safety Data Sheet (MSDS).
Storage and re-use
Ensure caps are replaced and product stored in a cool dry place.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours.
Features:
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Quick setting in 5 minutes
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling (surfaces need not mate closely)
Good chemical resistance
Appearance:
Clear with a slight yellow tinge
Where can this product be used?
Bakelite – joining or repairing
Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots
Repairing splits or cracks in a tennis racket
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Rigid Plastic
Crystal
Leather
How to use this product:
General Use
-Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
-All traces of grease, rust paint, etc. should be removed.
-For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
-Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick.
Safety tips:
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Do not use solvents near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non toxic when set.
For further information refer to the Material Safety Data Sheet (MSDS).
Storage and re-use
Ensure caps are replaced and product stored in a cool dry place.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours.
Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Very quick setting in 90 seconds
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling
Good chemical resistance
Where can this product be used?
General small household repairs
Fixing gemstones to mounts
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Most Plastics
How to use this product
General Use
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately.
Ensure correct caps are replaced on each tube or they will adhere.
Handy tips
Note: For information on how to identify plastics refer to the Selleys plastics guide.
For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured Araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping recommended for a stronger bond.
Singles are great for those unexpected household breakages, so keep a couple at home just in case.
Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours.
Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Very quick setting in 90 seconds
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling
Good chemical resistance
Where can this product be used?
General small household repairs
Fixing gemstones to mounts
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Most Plastics
How to use this product
General Use
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately.
Ensure correct caps are replaced on each tube or they will adhere.
Handy tips
Note: For information on how to identify plastics refer to the Selleys plastics guide.
For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured Araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping recommended for a stronger bond.
Singles are great for those unexpected household breakages, so keep a couple at home just in case.
Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6–8 hours, with maximum bond strength after 3 days.
Features
Stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries clear
Very strong and durable bonding
High water resistance (suitable for tiles around pools, but not below the water line for that use Selleys Knead It Aqua)
Forms a rigid, durable bond
Can be used for gap filling (surfaces need not mate closely)
Good chemical resistance
Heat resistant
Clamping recommended for stronger bond
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 80°C but is regained when temperature drops
Appearance
Translucent
Where Can This Product Be Used?
Load-bearing repairs
Gluing the head back on a hammer
Fixing loose table or chair legs
Bonding aluminium sheeting
Bonding timber on boats
Repairing splits and cracks in cricket bats
Bonding fibreglass sheets
Repairing skis
Fixing Dynabolts and metal rods into concrete
Suitable Materials
Glass
Metal
Wood
Fabric
Rigid plastics (except Polyethylene and Polypropylene)
Crystal
Leather
How to Use
Ensure all surfaces are clean, dry, and free from grease, rust, or paint.
For best results, roughen smooth surfaces after solvent cleaning.
Dispense equal volumes of Part A and Part B onto a clean disposable surface (e.g. cardboard or polyethylene) and mix thoroughly.
Apply adhesive immediately to both surfaces and press together.
Clamp the bond for 6–8 hours while setting.
Scrape off excess adhesive and clean utensils immediately.
Handy Tips
Mix in small quantities for longer working time — large mixes cure faster.
Replace caps immediately after use and wipe nozzles with acetone or nail polish remover before sealing.
Ensure caps are placed on the correct tubes (they are colour-coded).
Remove uncured adhesive with acetone or nail polish remover.
Once cured, remove by mechanical scraping or sanding — solvents will not dissolve the product.
To reposition a cured bond, heat slowly to at least 150°C (if safe for the material), then scrape off excess and reposition carefully.
For cleaning surfaces before use:
Porous surfaces use Selleys Liquid Sugar Soap
Non-porous surfaces (e.g. glass, metal) — clean with methylated spirits
For stubborn residue use Selleys Kwik Strip Smart
Ensure the surface is dry before applying.
Safety Tips
Avoid contact with skin and eyes.
Avoid breathing vapour.
Do not use solvents near eyes or open wounds.
In case of eye contact, flush with water for 15 minutes and seek medical attention.
Non-toxic when set.
Refer to the Material Safety Data Sheet (MSDS) for more information.
Storage & Reuse
Replace caps tightly after use.
Store in a cool, dry place.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days.
Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Very Strong, durable bonding
Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua)
Forms a rigid, durable bond
Can be used for gap filling (surfaces need not mate closely)
Good chemical resistance
Heat Resistant
Clamping is recommended to achieve a stronger bond
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 80°C but strength is regained when temperature drops
Where can this product be used?
Load bearing repairs
Gluing the head back on your hammer
Fixing loose table or chair legs.
Bonding solid pieces of Aluminium sheeting
Bonding timber on your boat
Repairing splits and cracks in Cricket bats
Bonding fibreglass sheets
Repairing Ski’s
Fixing Dynabolts and metal rods into concrete
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics
Crystal
Leather
How to use this product
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately.
When using tubes, Ensure correct caps are replaced on each tube or they will harden
Handy tips
For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping recommended for a stronger bond.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A strong and durable, fast setting two part epoxy adhesive that dries crystal clear making it ideal for areas where an invisible bond is required. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Weather and yellowing resistant. Shock resistant.
Features:
-Araldite is stronger than other glues due to the chemical reaction of the two parts.
-Bonds a variety of surfaces
-Dries Crystal Clear so there’s no visible evidence of repair
-Quick setting in 5 minutes
-No clamping necessary
-High water resistance
-Forms a rigid, durable bond
-Can be used for gap filling (Surfaces need not mate closely)
-Good chemical resistance
-Heat Resistant
-Doesn’t yellow over time so is ideal for use on glassware
Appearance:
Crystal Clear
Where can this product be used?
-Fixing a broken glass vase
-Repairing jewellery
-Toy repairs
-Fixing ornaments or crockery
-Fixing your handbag strap
-Not suitable for bonding plastics such as Polypropylene and Polyethylene or for use on polystyrene
-What materials is this product suitable for?
-Glass
-Metal
-Wood
-Fabric
-Rigid Plastic – refer to Selley's plastic guide for more info
-Crystal
-Leather
How to use this product:
-Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
-All traces of grease, rust paint, etc. should be removed.
-For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
-Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
-Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow the bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately.
-When using tube kit, ensure correct caps are replaced on each tube or they will adhere.
Handy tips:
-A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol).
-Clamping is recommended for a stronger bond.
-For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
-To extend product life replace caps immediately after use.
-When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
-Wipe off any uncured Araldite with acetone or nail polish remover.
-To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
-To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
-Keep a box of Selleys Sugar Soap Wipes around for quick & effective cleanup
-For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart.
Safety tips:
-Avoid contact with the skin and eyes.
-Avoid breathing vapour.
-Do not use solvents near eyes or open wounds.
-In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
-Non-toxic when set.
Storage and re-use:
Ensure caps or lids are replaced and product stored in a cool dry place.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A strong and durable, fast setting two part epoxy adhesive that dries crystal clear making it ideal for areas where an invisible bond is required. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Weather and yellowing resistant. Shock resistant.
Features:
-Araldite is stronger than other glues due to the chemical reaction of the two parts.
-Bonds a variety of surfaces
-Dries Crystal Clear so there’s no visible evidence of repair
-Quick setting in 5 minutes
-No clamping necessary
-High water resistance
-Forms a rigid, durable bond
-Can be used for gap filling (Surfaces need not mate closely)
-Good chemical resistance
-Heat Resistant
-Doesn’t yellow over time so is ideal for use on glassware
Appearance:
Crystal Clear
Where can this product be used?
-Fixing a broken glass vase
-Repairing jewellery
-Toy repairs
-Fixing ornaments or crockery
-Fixing your handbag strap
-Not suitable for bonding plastics such as Polypropylene and Polyethylene or for use on polystyrene
What materials is this product suitable for?
-Glass
-Metal
-Wood
-Fabric
-Rigid Plastic
-Crystal
-Leather
How to use this product:
-Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
-All traces of grease, rust paint, etc. should be removed.
-For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
-Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
-Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow the bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately.
-When using tube kit, ensure correct caps are replaced on each tube or they will adhere.
Handy tips:
-A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol).
-Clamping is recommended for a stronger bond.
-For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
-To extend product life replace caps immediately after use.
-When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
-Wipe off any uncured Araldite with acetone or nail polish remover.
-To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
-To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
-Keep a box of Selleys Sugar Soap Wipes around for quick & effective cleanup
-For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart.
Safety tips:
-Avoid contact with the skin and eyes.
-Avoid breathing vapour.
-Do not use solvents near eyes or open wounds.
-In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
-Non-toxic when set.
Storage and re-use:
Ensure caps or lids are replaced and product stored in a cool dry place.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
The special repair material is made from plasticine making it easy to mold and process for various uses. It is great for fixing the fuel tank or bed of your truck and great for metal tubs, radiators, or metal shelving units at home. When the material has fully cured it will be fully resistant to water, gasoline, oil, and other similar liquids.
Get professional results with the DIY Smart Repair while saving time and money
The 9-part Metal-FIX repair kit includes:
1 pair of rubber gloves
2x 0.99 oz repair compound tubes
1x alcohol-based cleaning cloth
1x sandpaper with 400 grain size
1x sandpaper with 800 grain size
1x plastic spatula
1x metal scraper
1x detailed instruction manual
Success in just 6 steps:
Thoroughly clean the parts to be repaired.
Sand the area with the included sandpaper.
Clean the area with the alcohol-based cloth.
Knead the required amount of repair compound.
Apply the compound to the damaged area.
Finally, even out and mold the compound with the trowel. You can process the sealed area after the repair compound has dried
Note: Read the instructions carefully before use.
FAQs:
Can it also be used to repair a hole in the motorcycle tank?
Yes, our "ATG Metal-Fix" is also suitable for the repair of tanks.
Is it also possible to seal/repair small holes in an aluminium pipework?
Yes, this set is also suitable for aluminium.
Can I also use this set for iron watering cans (holes on the bottom)?
Yes, even small holes in an iron watering pot can be sealed/repaired.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bastion Bond Breaker Joint Sealant
Professional silicone bond breaker for wet areas. Create a flexible, waterproof separation at wall to wall and wall to floor junctions so your membrane and tile system can move without cracking. Ideal for bathrooms, showers, laundries and balconies.
Why choose this sealant
Permanently flexible to absorb movement in corners and junctions
Neutral cure silicone suitable for use with most waterproofing membranes
Low odour, low VOC, indoor use friendly
Excellent adhesion to common building materials including concrete, masonry, ceramic tile, porcelain and most metals
Water resistant once cured and designed for wet area applications
Easy to gun out and tool for a smooth finish
Typical uses
Forming a bond breaker fillet in shower bases, bathrooms and laundries before waterproofing
Movement joints at internal corners prior to tiling
General wet area sealing where a flexible joint is needed
Surface preparation
Ensure surfaces are clean, dry and free from dust, oil, loose material and old sealant.
Mask adjacent edges for a neat finish if required.
For wide gaps, insert backing rod to control sealant depth.
How to apply
Cut the cartridge nozzle to the desired bead size and load into a standard caulking gun.
Gun a continuous bead into the corner or joint. Aim for a smooth cove fillet in the 5 to 12 mm range.
Tool the bead with a spatula or rounded tool to compact and shape it. Remove masking tape while the sealant is still wet.
Allow the bond breaker to skin before applying compatible waterproofing membranes over the area. Follow your membrane manufacturer’s recoat time.
Cure and finishing
Skin time is typically minutes depending on temperature and humidity.
Full cure occurs over 24 to 48 hours for standard beads. Thicker sections require longer.
After the membrane has cured, complete tiling and finish perimeter joints with a sanitary grade silicone.
Clean up
Wipe away excess immediately with a clean cloth.
Once cured, remove mechanically by trimming and peeling.
Handy tips
Not paintable. If painting is required, paint adjacent surfaces before sealing.
Always use backing rod for large joints to control sealant depth and reduce three sided adhesion.
Pre test on sensitive or natural stone surfaces.
Do not use in continuously immersed conditions or for structural glazing.
Storage and packaging
Cartridge size: 300 mL
Store upright in a cool, dry place. Use before the best by date printed on the cartridge.
Safety
Use in a well ventilated area. Avoid contact with skin and eyes. Keep out of reach of children. Refer to the product label for first aid directions.
In the box
1 x 300 mL cartridge of Bastion Bond Breaker Joint Sealant
1 x application nozzle
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bastion High-Bond Stud Adhesive 5.2 kg is a reliable stud adhesive for fixing plasterboard to timber or metal framing chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 5.2 kg pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Bastion High-Bond for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Bastion High-Bond Stud Adhesive 5.2 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Plasterboard installation on studs
Reducing screw count by bonding and fixing together
Renovations where clean bond lines are important
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Timber studs
Galvanised metal studs
Plasterboard back surfaces
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of work within the wet time window to ensure transfer. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Applies as a bead to studs. Press board into place and fix with screws while the adhesive is wet. Final cure occurs as the solvent or moisture leaves the bead.
Temperature and environmental performance
Use in dry, shaded conditions during lining work. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Remove fresh smears with a suitable cleaner. Trim cured squeeze out before finishing. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Store closed and away from heat sources. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Product Overview:
Bastion Multipurpose Primer is a professional-grade waterproofing primer designed for wet areas and tiled surfaces. It enhances adhesion for waterproofing membranes, adhesives, and coatings, making it ideal for use in bathrooms, kitchens, balconies, and other areas exposed to moisture. It is compatible with most construction adhesives and offers rapid drying for faster project completion.
Features & Benefits:
✔️ Multipurpose Use – Suitable for internal & external applications on walls and floors
✔️ Enhances Adhesion – Ensures strong bonding for tiles and waterproof membranes
✔️ Rapid Drying – Reduces wait times and speeds up installation
✔️ Low VOC Formula – Environmentally friendly with minimal odour
✔️ High Coverage – Approx. 5m² per litre for cost-effective application
Surface Preparation:
Ensure surfaces are clean, dry, and free from dust, grease, and other contaminants.
Remove loose particles and repair any cracks before application.
Porous surfaces may require multiple coats for optimal adhesion.
Application Instructions:
Shake well before use.
Apply using a brush, roller, or spray for even coverage.
Allow to dry for approximately 30 minutes before applying waterproofing membranes or adhesives.
For highly absorbent surfaces, apply a second coat after the first has dried.
Coverage:
1L covers approx. 5m² (depending on surface porosity and application method).
Drying Time:
Touch dry: 15-30 minutes
Ready for membrane or adhesive application: 30-60 minutes
Clean-Up:
Clean tools immediately with warm, soapy water before the primer dries.
Dispose of residue according to local waste disposal regulations.
Technical Data:
Type: Acrylic-based primer
Colour: Milky white (dries clear)
VOC Content: Low
Application Temperature: +10°C to +35°C
Storage: Store in a cool, dry place away from direct sunlight
Safety Warnings:
Avoid contact with skin and eyes; wear protective gloves and eyewear.
Use in a well-ventilated area to prevent inhalation of fumes.
Keep out of reach of children.
Refer to the Safety Data Sheet (SDS) for detailed handling information.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bastion Premixed Tile Adhesive 15 kg
Overview
Bastion Premixed Tile Adhesive 15 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework.
Why choose this product
Reliable bond performance supported by proven chemistry and rigorous quality control.
Smooth, predictable application that helps reduce mess and cleanup time.
Versatile adhesion profile suited to a wide range of substrates and project types.
Clear guidance on surface preparation, application method, and curing to help achieve the best possible result.
Suitable for residential fit-outs, maintenance, repairs, and light commercial projects.
Suitable materials
ceramic tiles
porcelain tiles
mosaics
stone suitable for porous adhesives
most interior substrates
Typical applications
General installation, repair, and maintenance where a durable bond is required.
Interior work that benefits from a neat finish and tidy joints.
Projects where dependable initial grab and high final strength are important.
Surface preparation
Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting.
Application
Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying.
Cut the nozzle to the required bead size or prepare the container according to the product type.
Apply an even bead or spread with a suitable trowel where required. Avoid trapping air.
Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting.
Support, clamp, or brace as needed until the adhesive develops sufficient handling strength.
Cure and working time
Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure.
Coverage
Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces.
Limitations
Do not apply to surfaces that are visibly wet unless the product specifically allows damp application.
Avoid continuous water immersion unless the product is rated for that exposure.
Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required.
Observe maximum service temperature and any movement or vibration limits appropriate to the application.
Clean up
Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers.
Safety
Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information.
Storage
Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first.
Troubleshooting
Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure.
Slow cure: Verify temperature and humidity. Increase airflow or allow more time.
Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins.
Frequently asked questions
Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first.
Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured.
What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat.
How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes.
Why buy from Glues Australia
We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bastion Superlite Lightweight Tile Adhesive 11 kg is a reliable lightweight polymer modified tile adhesive with excellent spread chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 11 kg pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Bastion Superlite for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Bastion Superlite Lightweight Tile Adhesive 11 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Large format wall and floor tiles
Substrates where reduced slump is beneficial
Renovations that require easy trowelling
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Concrete and screeds
Fibre cement sheet
Existing tiles suitably prepared
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of per data on the bag for open time and adjust for ambient conditions. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Observe recommended open time and bed thickness. Allow the adhesive to set before grouting and traffic.
Temperature and environmental performance
Install in mild weather to ensure predictable curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Clean trowels and buckets with water before the mix hardens. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Store the bag sealed in a dry place off the ground. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
BBQ Tough Clean Grease & Grime Spray 400 g
Bring your grill back to spotless condition with BBQ Tough Clean. This powerful, non-caustic formula is specially designed to lift away grease, fat, and charred food from BBQ plates, grills, and racks, giving you a cleaner and healthier cooking surface without harsh fumes.
Key Benefits:
Powerful cleaning: Penetrates and dissolves stubborn grease and grime.
Spotless results: Leaves BBQ surfaces residue-free for safer cooking.
Non-caustic & low fume: Safer to use around your outdoor cooking area.
Cold application: Designed to work when the BBQ is cool (before use).
Perfect For:
Stainless steel and cast iron BBQ plates, grills, and racks
Removing built-up food, grease, carbon deposits
Deep cleaning before a big barbecue or regular maintenance
How to Use:
Make sure your BBQ is cold. Remove the racks, grills and plates if possible.
Scrape off excess debris and wipe loose grease.
Shake the can well and spray liberally onto the surface from upright position.
Allow to sit at least 10 minutes (for tough grime, up to 2 hours), then wipe with a damp cloth or scouring pad.
Rinse thoroughly with water and dry with a clean cloth.
Optional: apply a light coat of cooking oil to surfaces to protect against corrosion.
Important Safety & Usage Notes:
Do not use on hot BBQs
Avoid spraying on painted, plastic or aluminum surfaces.
If overspray lands on unintended areas, wipe off immediately and rinse.
Not intended for use on exterior, non-cooking surfaces (use an exterior BBQ cleaner for those parts).
Keep out of reach of children and pets. Use protective gloves and avoid inhaling fumes.
![3M Claw Drywall Picture Hanger 15lbs 7Kg [Pack x 1]](//gluesaustralia.com.au/cdn/shop/files/638060661543_46481795-b414-41bc-a9c1-dc9b380c967f.jpg?v=1754712835&width=645)
![3M Claw Drywall Picture Hanger 15lbs 7Kg [Pack x 5]](//gluesaustralia.com.au/cdn/shop/files/638060661550_1fe37b78-c060-4f27-8387-63c1e448c0e6.jpg?v=1754712834&width=645)
![3M Claw Drywall Picture Hanger 25lbs 11Kg [Pack x 1]](//gluesaustralia.com.au/cdn/shop/files/638060661567_47226083-6c1f-44e5-9a7f-4238c8ab3fcf.jpg?v=1754712832&width=645)
![3M Claw Drywall Picture Hanger 25lbs 11Kg [Pack x 4]](//gluesaustralia.com.au/cdn/shop/files/638060661574_fb2086bb-b8e6-4490-8e91-ea0a14fda213.jpg?v=1754712831&width=645)
![3M Claw Drywall Picture Hanger 45lbs 20Kg [Pack x 1]](//gluesaustralia.com.au/cdn/shop/files/638060661581_a0340f7e-ce42-40cb-b71a-cd5b0abb2b66.png?v=1754712829&width=645)
![3M Claw Drywall Picture Hanger 45lbs 20Kg [Pack x 3]](//gluesaustralia.com.au/cdn/shop/files/638060661598_a9209f0c-7031-48ec-be4f-9fb1e87b6730.jpg?v=1754712828&width=645)
![3M Claw Drywall Picture Hanger 65lbs 30Kg [Pack x 2]](//gluesaustralia.com.au/cdn/shop/files/638060921234_e9940663-65b0-41b5-a196-e209139e4251.jpg?v=1754712826&width=645)
![3M Claw Drywall Picture Hanger 15lbs 7Kg [Pack x 1]](http://gluesaustralia.com.au/cdn/shop/files/638060661543_46481795-b414-41bc-a9c1-dc9b380c967f.jpg?v=1754712835&width=645)
![3M Claw Drywall Picture Hanger 15lbs 7Kg [Pack x 5]](http://gluesaustralia.com.au/cdn/shop/files/638060661550_1fe37b78-c060-4f27-8387-63c1e448c0e6.jpg?v=1754712834&width=645)
![3M Claw Drywall Picture Hanger 25lbs 11Kg [Pack x 1]](http://gluesaustralia.com.au/cdn/shop/files/638060661567_47226083-6c1f-44e5-9a7f-4238c8ab3fcf.jpg?v=1754712832&width=645)
![3M Claw Drywall Picture Hanger 25lbs 11Kg [Pack x 4]](http://gluesaustralia.com.au/cdn/shop/files/638060661574_fb2086bb-b8e6-4490-8e91-ea0a14fda213.jpg?v=1754712831&width=645)
![3M Claw Drywall Picture Hanger 45lbs 20Kg [Pack x 1]](http://gluesaustralia.com.au/cdn/shop/files/638060661581_a0340f7e-ce42-40cb-b71a-cd5b0abb2b66.png?v=1754712829&width=645)
![3M Claw Drywall Picture Hanger 45lbs 20Kg [Pack x 3]](http://gluesaustralia.com.au/cdn/shop/files/638060661598_a9209f0c-7031-48ec-be4f-9fb1e87b6730.jpg?v=1754712828&width=645)
![3M Claw Drywall Picture Hanger 65lbs 30Kg [Pack x 2]](http://gluesaustralia.com.au/cdn/shop/files/638060921234_e9940663-65b0-41b5-a196-e209139e4251.jpg?v=1754712826&width=645)
