Selleys All Plastics Glue - Strong and fast bond Perfect For Broken Toys (Glue + Primer) 3ml
Easy to use, fast setting adhesive system to repair ALL plastics.
-Bonds ALL Plastics, including Polyethylene (PE) and Polypropylene (PP)
-Easy to Apply
-Dries clear for clean, neat results
-Fast Bond: 2-30 seconds
-No clamping necessary
-No mixing required
-self-piercing, clog-free cap on adhesive
-Also bonds plastic to other surfaces: Metal, timber, china, rubber, leather
Where can this product be used?
-For interior projects and repairs
-For fast & easy repair of household items made from plastic
-Repair Toys & Games
-Fix Car accessories
-Repair Kitchen plastics and utensils
-Repair Office items
-Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet
-Best results for Nylon items (e.g. car parts) are achieved without initial priming. Contact Selleys consumer advice if unsure of plastic type.
-Not suitable for use on glass – we recommend Selleys Araldite Ultra Clear.
What materials is this product suitable for?
-Adhering Plastic to
How to use this product
-Ensure the surfaces to be joined are close fitting, clean, dry and free of dust.
-Using the primer pen, liberally coat plastic surface/s that are to be bonded.
-Pierce seal at end of the adhesive tube by attaching nozzle and cap and turning clockwise.
-Remove cap and apply a very small amount of glue to one surface only. Bring surfaces together and apply slight pressure.
-The adhesive will grab within 2-30 seconds, depending on environmental conditions and materials being bonded.
-Allow at least 30 minutes for sufficient bond strength for practical use.
-Wipe tip of the tube, replace the cap and store upright in a dry cool place.
-If using on leather test on an inconspicuous area first as adhesive may cause leather to discolour or harden.
-Not suitable to repair items that will contain hot liquids.
-Best results for nylon items are achieved without Initial priming (e.g car parts). Contact Selleys Consumer Advice if unsure of plastic type.
-Will also bond plastic to non-plastic surfaces (Metals, Timber, China, Rubber, Leather). Do not use primer on non-plastic surfaces.
-After use, wipe excess product from the adhesive nozzle with a tissue dipped in nail polish remover.
-For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
-In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in the hot soapy water.
-Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use.
-Keep Out of reach of Children
-Avoid contact with skin and eyes and avoid breathing in the vapour.
-Bonds on contact. Should fingers stick together apply a solvent such as acetone (nail polish remover) to contact areas then wash with water.
-Do not use solvents near eyes or open wounds.
-Highly Flammable, keep away from sources of ignition.
-Contents of the pen may cause lung damage if swallowed.
-This product is hazardous according to the criteria of NOHSC and HSNO. For frequent hobby or occupational use, please refer to the Material Safety Data Sheet.
-For Advice, contact a Poisons Information Centre (phone Aust. 131 126, NZ 0800 764 766) or a doctor.
-In case of eye contact immediately flush with water for at least 15 minutes and seek medical attention.
Storage and re-use
-Ensure caps are replaced and store in a cool dry place.
|Unit Of Measure||each|
Quick easy solution for my needsBy: Daniel Y on 9 November 2018It does exactly what it says it does, quick and easy to use. I used it to repair a model car that I had been keeping for ages. Now it's all fixed and displayed in my colleciton. Thanks for prompt delivery
Others Also Bought
More From This Category