Fast setting liquid supa glue in a self-standing bottle with brush applicator. Dries clear.

Features
Bonds a variety of surfaces
Extremely fast setting
Dries Clear for clean, neat results
Water resistant
No clamping necessary
No mixing required
Maximum strength achieved in 12 hours
Only takes 45 seconds to achieve an initial bond
Ideal for craft and collage applications
Forms a rigid bond
Easy to spread over wider areas from a stable self-standing bottle

Where can this product be used?
Useful for jobs with a wide surface area in both a repair and create capacity.
Water resistant, not waterproof, therefore not suitable for surfaces that will be continually wet
Not suitable for bonding plastics such as Polypropylene and Polyethylene.
Leather may become hardened or discoloured
For interior use only
Not suitable for repairing items that are in direct contact with hot liquids
Will not permanently bond glass or materials containing alkaline elements.
Has no gap filling properties, therefore, surfaces need to be a close fit
Not recommended for highly porous surfaces

What materials is this product suitable for?
Bonds a variety of porous and non-porous surfaces
Metals
China
Rubber
Leather
Some plastics
How to use this product
Supa Glue works best when the surfaces to be bonded are close fitting.
Surfaces to be bonded should be clean, dry and free of dust.
Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure.
The product grabs within 10-60 seconds, depending on environmental conditions and substrates to be bonded.
Allow 30 minutes for sufficient bond strength for practical use.
Ensure cap is replaced immediately after applying adhesive, as this prolongs the life of brush applicator.

Handy tips
Cyanoacrylate adhesives can create a white residue on the surface of a substrate if the area is not well ventilated. Clean the affected area with acetone to remove residue.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
Excellent when used with other adhesives, as the temporary tack
For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting
In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water.
Acetone (nail polish remover) or Olive oil can also be used to remove Quick Fix from the skin.
While superglue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24hours to dry, then drop more glue on the break area like a ‘collar’/protective layer.
Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions.
Super glues cure more slowly when large amounts are used. For faster cure use sparingly.
To remove excess from substrates, it is recommended that the material is soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbent material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method.

Safety tips
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Quick Fix Supa glue bonds on contact, if fingers should stick together, apply a solvent such as acetone to affected areas and wash off with water.
If no solvent is available wash area with warm soapy water and work fingers apart.
Do not use solvents near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non-toxic when set
Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin.

Storage and re-use
After use, tap bottle lightly on a flat surface to clear excess product from the nozzle.
Ensure cap is replaced and store in a cool dry place.
Store Upright.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.